machine knitting midgauge standard bulky machknit knit machine-knit patterns

Thursday, April 15, 2021

Machine Knit Cotton Hot Pads

 


I am on a mission to use up some of my huge cotton stash.  Have knit a lot of dishcloths, but thought it would be fun to be a little more creative---and make something useful.  I now have a cache of little gifts on hand.

Here’s how I have done them:

 *Used all cotton yarn and my standard gauge Brother 970 machine.  My designs are approx. a gauge of 7 st and 10 r to the inch, but it doesn’t matter. Mine end up to be between 7 and 9 inches wide by approximately the same height. You could use wool---haven’t tried because I am trying to use up the cotton.  You could also do these with a punch card machine or knit them plain.  But , where’s the fun in plain???

*Start with several rows of waste yarn with a quick cast on.  Engage the design with your electronics, then just knit not doing a permanent cast on with main yarn.  I tried to be sure to do the design so that the carriage ends at the right side when adding contrast yarn. The designs are knit in one longish rectangle.  Might want to switch between KC I and KC II for some rows so you don’t have a contrast yarn going all the way across the knitting for no good reason.  When the design is done, the bottom row is seamed to the top row.

* Some of your designs may have long floats.  Not to worry.  They add to the insulation factor.  I had no trouble with the stitches not conforming to one another or splitting between stitches, but if you do have this issue you can latch up the long float to a matching color. No one sees the inside.

* You may wonder why you need more rows in the middle of a design when both bottom and top halves are the same.  I found out the hard way that you need about 4 rows to go around the “bend” when you seam bottom to top or it’s off.  If you only want to do the bottom half of the design, that’s fine.  Just remember to do the same rows as the design and add 4 extra rows.  Example—the design is 86 rows.  Knit the 86, do 4 rows plain, knit 86 rows plain.

*Adding a loop in the corner is optional.  I did about 6 stitches x 50-60 rows, plain knitting since it curls like I cord anyway.  Looks nice if you hang the front corner with wrong side facing, knit the loop, then pick up stitches from the back side, knit a row and bind off.  When you seam the sides you can hide the purl bumps.

* To seam bottom to top, you have two options:

              -The Perfectionist option is to take the piece off on waste yarn when the design is complete, turn it so the right side is facing you, hang bottom to top stitches.  Then bind off. The seam will be on the inside and not show.

              -The quicker, easier way is to hang the beginning stitches onto the top stitches when the piece is complete, then bind off around the gate pegs.  You will have a seam on the right side.  I think it looks ok. On one I ran out of main yarn right when I needed ONE MORE ROW!  So I used the contrast yarn to bind off.  So one row was main and one contrast.  I actually liked it--- it created a decorative stitch.

* Options for insulation for the middle of the hot pad--- I have used layers of insulbright, >1 layer of flannel cotton fabric (laundered first),  knitted squares of cotton yarn I didn’t like, old cotton cut to size swatches, machine sewed around edges so they wouldn’t unravel, cotton quilting batting, old clean towels.  After completing the knitting, I turned it wrong side out, then tacked the lining to the outer in several places, so it wouldn’t shift.  I used regular matching cotton sewing thread. Doesn’t show if you take tiny stitches.  When you are sure the lining won’t shift, turn right side out.

 * Finally, remove waste yarn and mattress stitch the side seams by hand with right side showing.

 

I used patterns that I have had in DAK for ages, some are built-in patterns, some are purchased—lots of Dale of Norway patterns.

Some examples-----------Have knitted abt 15 so far.  Addictive. Can you tell I love Norwegian designs??? 

 

I plan to tell a recipient to hand wash cold, dry flat.  I don't want them (the hotpads) to shrink and pucker up. 😊

My absolute favorite is the rosemaling design.  It was a free chart on the Dale of Norway site.  I converted the chart to a DAK file.  If you would like to have it, write to me.  I don't know how to attach a file here with Blogger.  If someone knows how, would like to be enlightened.

6 comments:

Knittedbrows said...

Love the designs and bright colours !!

Mar said...

Thank you! Wish I could say that my stash has noticeably diminished...

Kate Clark said...

Mar,
What a great idea. I was just looking at my old tattered pot holders and thinking of buying new ones. This is a lot more fun and I have everything I need to do it! Thank you!!!
Kate

Anonymous said...

How many did you cast on?

Anonymous said...

How many stitch’s do you cast on?

Mar said...

It depends on the design you are using and the size you want it to be, especially if you want the design to be symmetrical. Mine are typically 70 to 80 stitches, give or take, and 100 rows to each side. Don't forget to add 4 turning rows.
I don't know what gauge you are getting or what yarn, so a little math would be in order. Maybe try making one with your calculations and adjust from there. I used really thin cotton yarn. Good luck! Not a hard project.