Baby Rib Warmer ©2015
by Mar Heck 
NOTES: Directions are given for Midgauge or Bulky
with Standard gauge machine in parenthesis.
There is no shaping required because the ribbing pulls in the knitting to
make the yoke shape and armholes. So if you have a ribber, this is a fairly
fast knit. If you need to hand manipulate the ribbing, it will take a little
longer. Because I have a ribber for my
Silver Reed 860 midgauge, I used a 2 x 2 rib in the yellow pictured example. I used a Brother 970 with ribber for the
standard gauge blue example pictured. If
you need to hand latch the ribbing, it would save a little time if you did a 2
x 1 rib. Check your manual or You Tube for
how to latch ribbings. Note that the rib tension is the same as the
stockinette. I think the pattern would
be suitable for a boy or girl baby. I
didn’t attempt to do the sweater in mock rib, but that might be worth a try too
if you don’t possess a ribber.
Yarn- whatever yarn gets the same gauge as listed
or your garment may come out a completely different shape, For the sample I used Lion Brand Pound of
Love pale yellow, just a few ounces. On
the standard gauge machine, I used Mary Lou’s Symphony, also a small amount.
Machine – midgauge or
bulky with standard in parenthesis, ribber if you have one
Gauge- on mid or bulky
4 stitches and 6 rows to one inch; for standard 7 stitches and 10 rows to one
inch. Tension dial will depend on the
yarn you use to get this gauge. Knit a
swatch to determine that. For both
samples I used tension 7, but your machine may be different.
Finished Size
– about 10 inches wide and 10 inches tall for a 6 to 12 month baby. For other sizes add or subtract an inch each
direction.
Directions
BACK
Cast on 40 (70) stitches in your favorite method for
ribbing doing 2 x 2 rib at (T7/7). Use
the same tension as you will use on the stockinette part. If you have a smaller rib cast on comb, use
that so that it doesn’t pull down so hard. Because there are fewer stitches
than on an adult garment, you won’t need so much weight but still some so that
the stitches knit off.
RC 000 Knit 6 (10) rows rib. Transfer rib stitches to main bed and change
to regular carriage for stockinette.
Knit stockinette stitch to RC 38 (66).
Change to rib carriage and transfer every other 2 st to ribber for
ribbing,. Knit to row 60 (100), transfer
rib stitches to main bed and bind off (not too tight).
LEFT FRONT
Cast on 20 (36) stitches in your favorite method for
ribbing doing 2 x 2 rib at (T7/7). RC000
Knit 6 (10) rows rib. Transfer
rib stitches to main bed and change to regular carriage for stockinette. Knit stockinette stitch to RC 38 (66). Change to rib carriage and transfer every other
two stitches to ribber for ribbing,. Knit
to RC 47 (79). For neck, bind off 10 (16)
stitches. On remaining 10 (20) stitches
knit to RC 60 (100). Transfer rib
stitches to main bed. Bind off these 10 (20) shoulder stitches.
RIGHT FRONT
Same as left front except knit to RC 48 (80) to bind
off neck stitches so that the carriage is on the correct side for binding off.
FRONT EDGING
I used what I call the “2 Row Wonder” for the front
edges. It is nice for baby cardi’s
because it’s dainty and helps the edge lie flat. It’s easy to incorporate buttonholes by
skipping stitches from the garment as you are hanging garment stitches.
Hold the edge up to the machine without stretching to
get an estimate of how many stitches you’ll need. With the wrong side of the edge facing you,
pick up whole stitches from the garment and hang on the needles. You may need to skip a garment stitch now and
then because you are matching stitches to rows. Also, for girls, put a button hole (or evenly
spaced button holes) on the garment’s right front and on the left for a boy.
After you knit
one front’s edge, write down the number of stitches you picked up so that the
other side turns out the same. Also, try
to get to the very edge of the ribbings on both sides so that the edge extends
all the way.
Push the needles all the way out on the first row to
aid the carriage in knitting. After the
first row, when a loop is formed for the buttonhole, hang it on the needle
above. Knit two rows total at garment
tension. Carriage is on the right. Bind off around the gate pegs. If your machine doesn’t have gate pegs, pull
a needle out to act as a gate peg to even out the stitches and make the rope-like stitch. The yarn goes to the right of this needle.
FINISHING
Stitch shoulder seams.
Mattress stitch side seams up to the point where the yoke ribbing
starts. Hide yarn ends and sew on a
button (buttons) securely. If the fronts
need a little steam to lie flat, be sure to not touch the yarn if you are using
an iron.
If you can’t achieve my
gauge, use this schematic and some math to achieve the same size as I did.
Interesting note…now that I have taken
pictures, I see that my midgauge machine knits at a different tension every
other row!!! Not too happy about this, but I don’t know if there is anything to
be done about it. It’s too consistent to
be my fault, right? Reminds me of hand knitting where the knitter uses a
different tension on purl vs knit rows. Actually,
in person it doesn’t look so noticeable.
Cameras can be mean sometimes.
Truth hurts. OH WELL…
Back view
love to see a picture if you do knit it.